The STTS75 is a high-precision CMOS (digital) temperature sensor IC with a delta-sigma analog-to-digital (ADC) converter and an I²C-compatible serial digital interface. It is targeted for general applications such as personal computers, system thermal management, electronics equipment, and industrial controllers, and is packaged in the industry standard 8-lead MSOP(TSSOP) and SO8 packages.

The device contains a band gap temperature sensor and programmable 9- to 12-bit ADC which monitor and digitize the temperature to a resolution up to 0.0625 °C. The STTS75 is typically accurate to (±3 °C - max) over the full temperature measurement range of –55 °C to 125 °C with ±2 °C accuracy in the –25 °C to +100 °C range. At power-up, the STTS75 defaults to 9-bit resolution for software compatibility with the STLM75.

The STTS75 is specified for operating at supply voltages from 2.7 V to 5.5 V. Operating at 3.3 V, the supply current is typically (75 μA).

The onboard delta-sigma analog-to-digital converter (ADC) converts the measured temperature to a digital value that is calibrated in °C; for Fahrenheit applications a lookup table or conversion routine is required.

The STTS75 is factory-calibrated and requires no external components to measure temperature.

stts75是一种高精度的CMOS（数字）与Δ∑模数转换器（ADC）温度传感器IC和一个I2C兼容的串行数字接口。这是针对一般的应用，如个人电脑、热管理系统、电子设备、工业控制器，并在包装行业标准的8引脚MSOP（TSSOP）和SO8封装

该器件包含一个带隙温度传感器和可编程的9 - 12位ADC监测和数字化的温度分辨率高达0.0625°C. stts75通常是准确的（±3°C max）在–55°C全温度测量范围为125°C±2°C准确的–25°C + 100°C系列。在上电，该stts75默认为9位与stlm75软件兼容分辨率。

stts75是操作电源电压从2.7 V到5.5 V操作在3.3 V的电源电流通常是指定的，（75μ一）

船上的Δ-∑模数转换器（ADC）转换成数字值，测得的温度是°C校准；为华氏应用查找表或转换程序是必需的。

是的stts75工厂校准，不需要外部元件来测量温度。

Key Features

• Measures temperatures from –55 °C to +125 °C (–67 °F to +257 °F)

• ±0.5 °C (typ) accuracy

• ±2 °C (max) accuracy from –25 °C to +100 °C

• Low operating current: 75 μA (typ)

• No external components required

• 2-wire I²C/SMBus-compatible serial interface

• Selectable serial bus address allows connection of up to eight devices on the same bus

• Thermometer resolution is user-configurable from 9 (default) to 12 bits (0.5 °C to 0.0625 °C)

• 9-bit conversion time is 45 ms (typ)

• Programmable temperature threshold and hysteresis set points

• Wide power supply range-operating voltage range: 2.7 V to 5.5 V

• Power saving one-shot temperature measurement

• Power-up defaults permit standalone operation as thermostat

• Shutdown mode to minimize power consumption

• Separate open drain output pin operates as an interrupt or comparator/thermostat output (dual purpose event pin)

• Packages:

• SO8

• MSOP8 (TSSOP8)

主要特点

测量温度从55°到125°（67°f）

±0.5°C（典型值）的精度

±2°C（最大）精度由- 25°为±100°

低工作电流：75μ一（典型值

无需外部元件

2线I2C和SMBus兼容串行接口

可选的串行总线地址允许多达八个设备在同一总线连接

温度计分辨率为用户配置的9（默认）为12位（0.5摄氏度至0.0625摄氏度）

9位转换时间为45毫秒（典型值）

可编程温度阈值和滞后集点

电源电压范围：2.7伏至5.5伏

节能一杆温度测量

电源默认允许独立运行作为温控器

关机模式，以尽量减少电力消耗

单独的开漏输出引脚作为一个中断或比较器/温控器输出（双目的事件引脚）

包装：

SO8封装

MSOP8（采用TSSOP8）