The STLM75 is a high-precision digital CMOS temperature sensor IC with a sigma-delta temperature-to-digital converter and an I²C-compatible serial digital interface. It is targeted for general applications such as personal computers, system thermal management, electronics equipment, and industrial controllers, and is packaged in the industry standard 8-lead TSSOP and SO8 packages.

The device contains a band gap temperature sensor and 9-bit ADC which monitor and digitize the temperature to a resolution up to 0.5 °C. The STLM75 is typically accurate to (±3 °C - max) over the full temperature measurement range of –55 °C to 125 °C with ±2 °C accuracy in the –25 °C to +100 °C range. The STLM75 is pin-for-pin and software compatible with the LM75B.

The STLM75 is specified for operating at supply voltages from 2.7 V to 5.5 V. Operating at 3.3 V, the supply current is typically (125 μA).

The on-board sigma-delta analog-to-digital converter (ADC) converts the measured temperature to a digital value that is calibrated in degrees centigrade; for Fahrenheit applications a lookup table or conversion routine is required.

The STLM75 is factory-calibrated and requires no external components to measure temperature.

stlm75是一个高精度的数字CMOS温度传感器IC采用∑-Δ温度数字转换器和一个I2C兼容串行数字接口。这是针对一般的应用，如个人电脑、热管理系统、电子设备、工业控制器，并在包装行业标准的8引脚TSSOP和SO8封装

该器件包含一个带隙温度传感器和9位ADC监测和数字化的温度分辨率高达0.5°C. stlm75通常是准确的（±3°C max）在–55°C全温度测量范围为125°C 2 C±°精度在–25°C + 100°C系列。是的stlm75引脚对引脚和软件兼容的lm75b。

stlm75是操作电源电压从2.7 V到5.5 V操作在3.3 V的电源电流通常是指定的，（125μ一）

车载Sigma-Delta模数转换器（ADC）转换为数字值，测量的温度是摄氏度校准；为华氏应用查找表或转换程序是必需的。

stlm75是工厂校准，不需要外部元件来测量温度。

Key Features

• Measures temperatures from –55°C to +125°C (–67°F to +257°F)

• ±0.5°C (typ) accuracy

• ±2°C (max) accuracy from –25°C to +100°C

• Low operating current: 125 μA (typ)

• No external components required

• 2-wire I²C/SMBus-compatible serial interface

• Supports bus time-out feature

• Selectable bus address allows connection of up to eight devices on the bus

• Wide power supply range-operating voltage range: 2.7 V to 5.5 V

• Conversion time is 150 ms (max)

• Programmable temperature threshold and hysteresis set points

• Pin- and software-compatible with LM75 (drop-in replacement)

• Power-up defaults permit standalone operation as a thermostat

• Shutdown mode to minimize power consumption

• Output pin (open drain) can be configured for interrupt or comparator/thermostat mode (dual purpose event pin)

• Packages:

• SO8

• MSOP8 (TSSOP8)

主要特点

测量温度从55°到125°（67°f）

±0.5°C（典型值）的精度

±2°C（最大）精度由- 25°为±100°

低工作电流：125μ一（典型值

无需外部元件

2线I2C和SMBus兼容串行接口

支持总线超时功能

可选总线地址允许连接多达八个设备在总线上

电源电压范围：2.7伏至5.5伏

转换时间为150毫秒（最大）

可编程温度阈值和滞后集点

引脚和软件兼容（下降LM75更换）

电源默认允许独立运行作为一个温控器

关机模式，以尽量减少电力消耗

输出引脚（开漏）可以配置为中断或比较器/温控器模式（双目的事件引脚）

包装：

SO8封装

MSOP8（采用TSSOP8）