The PIC18F14K50 brings advanced features and exceptional value to the embedded USB market.This low cost PIC® Microcontroller features a full speed USB 2.0 compliant interface that can automatically change clock sources and power levels upon connection to a host, making it an exceptional device for battery-powered applications. The addition of mTouch(TM) touch sensing compatibility, a 10-bit ADC, motor control PWMs, and a host of serial interfaces make the PIC18F14K50 the perfect device to "Just add USB" to any application.
Debug Support
• A debug header is required for this device
• Part Numbers:, AC244023 (F) / AC244024 (LF)
• Debug and programming support is available via MPLAB® REAL ICE, PICkit™ 3, and MPLAB® ICD 3
• For Debug Header information, please refer to
C Compiler optimized architecture
Self-programmable under software control
Support for Interrupt Priority Levels
8x8 Single-Cycle Hardware Multiplier
Enhanced Watchdog Timer with a programmable period
Full Speed Universal Serial Bus InterfaceUSB v2.0 compliant interface
Supports both Low Speed and Full Speed operation
Supports Control, Interrupt, Isochronous and Bulk transfer
Up to 16 Endpoints (or up to 8 bidirectional)
Automatic detection of physical connection to USB host
256-byte Dual Access RAM
Flexible Clocking OptionsCan be internally clocked up to 48MHz
Fully tunable Internal Oscillator
Supplies frequencies from 31KHz to 16MHz
Can be user-adjusted for frequency drift
Internal 4x Phase Lock Loop (PLL)
Can be used with External or Internal Oscillators
Fail-safe Clock Monitor
Allows for safe shutdown during oscillator failure
Advanced PIC® Microcontroller PeripheralsDual Capture/Compare/PWM interfaces
Up to 5 PWM Outputs
Programmable dead time, auto shutdown/restart
Master I2C/SPI Interface
Supports all modes of 3-wire SPI
I2C™Compatible Master and Slave modes with address masking
Enhanced Addressable USART Module
Supports RS-485, RS-232, and LIN 2.0
10-bit, 9-channel ADC Module
Can acquire & convert samples automatically
Can operate in sleep mode
mTouch(TM) compatible Analog Comparators w/ SR Latch
Rail to Rail operation
Independent input multiplexing
Robust GPIO with 25mA sink/source current
Programmable On-chip Voltage Reference
Can be used with Comparators or ADC
Operating Environment Versatility1.8 to 5.6V Operating Range
Software Programmable Brown-out Reset feature
Four power-managed operating modes
Two-speed clock startup option
PIC18F14K50 封装图
PIC18F14K50 封装图
PIC18F14K50 封装图
PIC18F14K50 封装图
型号 | 制造商 | 描述 | 购买 |
---|---|---|---|
PIC18F14K50-E/SS | SiTime | 有源晶振 3.3V ±50ppm 166.666MHz SMD-4 | 立即购买 |
PIC18F14K50-E/SO | Epson | 有源晶振 33MHz 5V SOJ-4 | 立即购买 |
PIC18LF14K50T-I/MQ | NorComp | CONN HEADER VERT 18POS 2MM | 立即购买 |
PIC18F14K50T-I/MQ | SiTime | 有源晶振 ±35ppm 3.3V 77.76MHz SMD-6 | 立即购买 |
PIC18F14K50-E/MQ | Abracon | 有源晶振 ±10ppm 2.25V~3.6V 16.384MHz SMD-6 | 立即购买 |
PIC18F14K50-E/P | SiTime | 有源晶振 33MHz 3.3V ±50ppm SMD-4 | 立即购买 |
在本案例中,本文将介绍如何将16×2 LCD显示屏连接到PIC18F系列的PIC18F4550单片机。
在无线图像传输通信系统中,要获得较高的接收增益,需要定向接收天线对准信号发射源。本文针对由指挥车和被控车辆组成的应用平台,利用磁罗盘和GPS的定向、定位技术设计了车载定向天线云台随动系统。在该系统中,定向...
随着科技的发展,印刷行业开始从传统的模拟生产转向数字化生产,墨斗作为胶印机的核心着色装置,其控制精度对胶印机的生产质量和自动化水平起着非常重要的作用。
遥控码是一串二进制数字信号,通过脉冲编码形成脉冲序列,被调制到一个固定频率载波上,最后通过红外发射管,以光脉冲的形式发射出去。脉冲编码就是将“1”和“0”用一个脉冲来标识。本设计使用NEC红外协议,用脉宽560u...
基于PIC18系列(PIC18F4520)单片机+DHT11的温湿度采集系统的设计与制作(Proteus仿真部分)
芯片烧录行业领导者-昂科技术近日发布最新的烧录软件更新及新增支持的芯片型号列表,其中昂科发布软件更新支持Microchip微芯的PIC18 Q84系列PIC18F26Q84的烧录已经被昂科的通用烧录平台AP8000所支持。
微芯PIC18F6内置LCD驱动器的64/80引脚高性能单片机
PIC18F4520-I/P开发板 学习板 核心板 标准版本 引出常用接口,可接微雪外围模块 型号 Open18F4520 (标准版)