The MD2134 is a high-speed source driver for use in a pulsed current waveform generator. This programmable, fast, arbitrary current level driver is designed for medical ultrasound imaging beamforming applications. It also can be used in HIFU, NDT ultrasound and other instrument applications.The MD2134 consists of CMOS digital logic input circuits, an eight-bit current DAC for aperture weighting amplitude control, and a programmable 15-level pulse amplitude modulation (PAM) current-source that does not include a zero level. The fast current sources are constructed with current-switch array, controlled by the LV0~LV15 level-register as the waveform data points. Four logic inputs M[3:0] are used for transmit data level selecting, as well as the transmitting timing control pins. Each level can be programmed to a resolution of +/-127 including zero (8-bit) in addition to an 8-bit SPI apodization DAC. The outputs PA and PB are controlled by M[3:0] pins directly, as well as the polarity-flip bit S1 in the SPI register. The high-speed SPI interface will achieve per-scan-line fast data updating for dynamically changing delay time, weighting and waveforms.The MD2134 outputs are designed to drive two very low-threshold, high-voltage depletion N-MOSFETs, such as DN2625s, as source drivers. The two DN2625 drains are connected to a center-tap RF pulse transformer. The transformer’s secondary output connects to a cable and piezoelectric or capacitive transducer as a load with a good impedance match.
Multiple-level ultrasound pulser
Fast switching current source for push-pull topology
250MHz maximum frequency, 4.0ns input to output delay
15 independent programmable output level registers
Pulse amplitude modulation (PAM) with 8-bit resolution
8-bit apodization DAC for peak output current via SPI
Very low second order harmonic distortion
Picoseconds time-jitter from input to output
Fast SPI write and read-back of level & DAC registers
+5.0V power supply, 2.5V CMOS logic interface
Drives DN2625 MOSFETs output up to 230VP-P
Programmable aperture windowing
MD2134 封装图
型号 | 制造商 | 描述 | 购买 |
---|---|---|---|
MD2134K7-G | - | - | 立即购买 |
我们使用的汽车正在向着绿色节能、网络化、智能化的方向发展,车载电子设备的计算能力越来越高,作为人机界面的屏幕显示效果越来越好,内容越来越丰富。
由于生成的md5信息中,每个md5值后都紧跟着对应的文件的路径(可能是相对路径),于是将生成的md5保存到某个文件中,以后可以使用该文件来检查md5值对应文件内容是否发生了修改。
OPA2134双列8脚封装,宽带为8MHz,转换速率为20V/us,输入失调电压为±0.5mv,具有8nv(HZ平方根)的噪声密度,0.00008%的失真系数和20V/us的上升速度。
OPA2134系列是超低失真,低噪声运算放大器,为音频应用完全指定。本文介绍了OPA2134引脚及特性,其次介绍了OPA2134封装信息与绝对最大额定值,最后介绍了三款OPA2134的应用电路。
本文主要介绍了五款opa2134应用电路图。0PA134系列运算amps是单位增益稳定和合适的对于音频和通用广泛的应用。所有电路是完全独立的双通道版本,保证正常的行为时,一个放大器在包装是过载或短路。电源pins应与10nF被绕过或...
由于售货机的功能不断增多,售货机控制系统也相应得不断变得庞大,这就使原来的面向过程的开发方法变得越来难以扩展和维护,根据自动状态机的理论,提出一种在售货机上的状态机模型,该模型对系统状态进行抽象和分离...
本文通过ARM7微处理器芯片LPC2134的GPIO实现了与内藏T6963C的液晶显示模块的接口设计,并在软件上实现了其基本显示功能,从而在满足了工程设计的要求。
随着电力系统的发展,其系统容量越来越大,结构越来越复杂,系统中的自控及继保装置所需处理的信息不断增加,这对人机接口的功能提出了更高的要求。新型的人机接口模块要能够
MCP9904 | MD1820 | MIC4830 | MCP1415 |
MIC2103 | MCP3919 | MIC2185 | MCP6G01 |
MJF15031 | MCP2030 | MMBFJ310L | MC74VHCT374A |
mpu6050 | MJ15001 | MC74VHC1GT86 | MC74LCX258 |
MC74HCT4094A | MJL4281A | MC10EP31 | MC10EL05 |