尊敬的客户:为给您持续提供一对一优质服务,即日起,元器件订单实付商品金额<300元时,该笔订单按2元/SKU加收服务费,感谢您的关注与支持!
    首页产品索引BQ24031-Q1

    BQ24031-Q1

    购买收藏
    汽车类具有动态电源通道管理、输出稳压的锂离子充电器双输入锂离子充电器

    制造商:TI

    产品信息

    描述 The bqTINY™ III series of devices are highly integrated Li-ion linear chargers and system power-path management devices targeted at space-limited portable applications. The bqTINY III series offer integrated USB-port and dc supply (AC adapter), power-path management with autonomous power-source selection, power FETs and current sensors, high accuracy current and voltage regulation, charge status, and charge termination in a single monolithic device.The bqTINY III series powers the system while independently charging the battery. This feature reduces the charge and discharge cycles on the battery, allows for proper charge termination, and allows the system to run with an absent or defective battery pack. This feature also allows for the system to instantaneously turn on from an external power source in the case of a deeply discharged battery pack. The IC design is focused on supplying continuous power to the system when available from the AC, USB, or battery sources. The power select pin (PSEL) defines which input source is to be used first (primary source is either AC or USB). If the primary source is not available, then the IC automatically switches over to the secondary source (if available) or the battery as the last option. If the PSEL is set low, the USB input is selected first and (if not available) the AC line is selected (if available) but programmed to a USB input limiting rate (100 mA/500 mA max). This feature allows the use of one input connector, where the host programs the PSEL pin according to what source is connected (AC adapter or USB port). The ISET1 pin programs the battery's fast-charge constant current level with a resistor. During normal AC operation, the input supply provides power to both the OUT (system) and BAT pins. For peak or excessive loads (typically when operating from the USB power, PSEL = low) that would cause the input source to enter current limit (or Q3 – USB FET limiting current) and its source and system voltage (OUT pin) to drop, the dynamic power-path management (DPPM) feature reduces the charging current attempting to prevent any further drop in system voltage. This feature allows the selection of a lower current rated adapter based on the average load (ISYS-AVG + IBAT-PGM), rather than a high peak transient load.特性 Qualified for Automotive Applications Small 3.5-mm × 4.5-mm QFN Package Designed for Single-Cell Li-Ion or Li-Polymer-Based Portable ApplicationsIntegrated Dynamic Power-Path Management (DPPM) Feature Allowing AC Adapter or USB Port to Simultaneously Power the System and Charge the Battery Power Supplement Mode Allows Battery to Supplement USB or AC Input Current Autonomous Power Source Selection (AC Adapter or USB) Integrated USB Charge Control With Selectable 100-mA and 500-mA Maximum Input Current Regulation LimitsDynamic Total Current Management for USB Supports up to 2-A Total Current 3.3-V Integrated LDO Output Thermal Regulation for Charge ControlCharge Status Outputs for LED or System Interface Indicates Charge and Fault Conditions Reverse Current, Short-Circuit, and Thermal Protection Power Good (AC Adapter and USB Port Present) Status Outputs Charge Voltage: 4.1 V or 4.2 V APPLICATIONSSmart Phones and PDAsMP3 Players Digital Cameras Handheld Devices Internet Appliances

    电路图、引脚图和封装图

    在线购买

    型号制造商描述购买
    BQ24031IRHLRQ1TIIC PWR MANAGEMENT SYSTEM 20-QFN 立即购买

    应用案例更多案例

    系列产品索引查看所有产品

    BAS16P2BELASIGNA 200BQ24735BFS17
    B82722-J2302-N1BZV55-C5V1BA10393F-E2BCP56-16T1G
    BQ24157SBCV26BAV74BAT54XV2
    BAT54STB39321B3761Z810BDX54CBD678G
    BAL-NRF02D3BAT54M3T5GBQ24232HBAT30F3
    Copyright ©2012-2024 hqchip.com.All Rights Reserved 粤ICP备14022951号工商网监认证 工商网监 营业执照