ADS7953
具有串行 I/F 的 12 位、1MSPS、16 通道、单端、微功耗 SAR ADC
制造商:TI
产品信息
描述 The ADS79xx is a 12/10/8-bit multichannel analog-to-digital converter family. The following table shows all twelve devices from this product family. The devices include a capacitor based SAR A/D converter with inherent sample and hold. The devices accept a wide analog supply range from 2.7 V to 5.25 V. Very low power consumption makes these devices suitable for battery-powered and isolated power supply applications. A wide 1.7-V to 5.25-V I/O supply range facilitates a glue-less interface with the most commonly used CMOS digital hosts. The serial interface is controlled by CS and SCLK for easy connection with microprocessors and DSP. The input signal is sampled with the falling edge of CS. It uses SCLK for conversion, serial data output, and reading serial data in. The devices allow auto sequencing of preselected channels or manual selection of a channel for the next conversion cycle. There are two software selectable input ranges (0 V to 2.5 V and 0 V to 5 V), four individually configurable GPIOs ( in case of TSSOP package devices), and two programmable alarm thresholds per channel. These features make the devices suitable for most data acquisition applications. The devices offer an attractive power-down feature. This is extremely useful for power saving when the device is operated at lower conversion speeds. The 16/12-channel devices from this family are available in a 38-pin TSSOP and 32 pin VQFN package and the 4/8-channel devices are available in a 30-pin TSSOP and 24 pin VQFN packages.特性1-MHz Sample Rate Serial DevicesProduct Family of 12/10/8-Bit ResolutionZero Latency20-MHz Serial Interface Analog Supply Range: 2.7 to 5.25 V I/O Supply Range: 1.7 to 5.25 VTwo SW Selectable Unipolar, Input Ranges: 0 to 2.5 V and 0 to 5 VAuto and Manual Modes for Channel Selection12, 8, 4-Channel Devices can Share 16 Channel Device Footprint Two Programmable Alarm Levels per ChannelFour Individually Configurable GPIOs for TSSOP package devices. One GPIO for QFN devicesTypical Power Dissipation: 14.5 mW (+VA = 5 V, +VBD = 3V) at 1 MSPSPower-Down Current (1 µA)Input Bandwidth (47 MHz at 3 dB)38-,30-Pin TSSOP and 32-,24-Pin QFN PackagesAPPLICATIONSPLC / IPC Battery Powered SystemsMedical InstrumentationDigital Power SuppliesTouch Screen ControllersHigh-Speed Data Acquisition SystemsHigh-Speed Closed-Loop SystemsAll other trademarks are the property of their respective owners
基于ADS对射频前端的接收端建模与仿真分析近年来,随着无线通信业务的迅速发展,通信频段已经越来越拥挤。1985年美国联邦通信委员会(FCC)授权普通用户可以使用902 MHz,2.4 GHz和5.8 GHz三个工业、科技、医学(ISM)频段。ISM频段为无线通信设备提供了无需申请在低发射功...
2010-06-04
2023-10-16
ADS生成bin的方法 ADS路径问题ADS生成bin的方法 Edit DebufRel settings Target Settings Post-Linker ARM fromELF 然后在 ARM FromELF Plain binary 下面的路径 似乎不用设置,空着就ok,我设了反倒出不来bin。奇怪。还有就是在代码框,也要设置DebufRel settings一遍,好像分开的。
2010-06-04
基于ADS的射频微波元器件模型库构建讲解教程仿真是早期验证最重要、最直观的手段,也是研发过程中发现问题和优化设计的重要途径。本文针对不同类型器件,提出了基于原理图模型、行为级模型以及 测试模型,建立射频微波模型库。其中,使用基于测试结果的X参数能...
2010-06-04
工程师如何使用ADS仿真?如何优化ADS仿真?工程师如何使用ADS仿真?如何优化ADS仿真?我需要详尽、详实、细致的最少1500字的文章 摘要: 高级设计系统(ADS)是一种强大的模拟和设计软件工具,被世界各地的射频和微波工程师所使用。在这
2023-10-20
2023-07-05
2018-07-06
2018-07-06